Table of Contents
    Home / Computers / Understanding PC Buses
    Computers 6 min read

    Think of a bus as the electronic highway on which data travels within a computer, from one component to another. This bus connects the CPU to the main memory (RAM) on the motherboard.

    Think of a bus as the electronic highway on which data travels within a computer, from one component to another. Basically, it’s the conduit used by your entire system to communicate with your CPU. A bus is a collection of wires and connectors through which the data is transmitted. When used in reference to personal computers, the term bus usually refers to what is commonly called the local bus (on older systems) or system bus (on newer systems). This bus is considered the first bus on the electronic highway and it connects the CPU to the main memory (RAM) on the motherboard. All buses consist of two parts — an address busand a data bus.

    The data bus transfers actual data whereas the address bus transfers information about the data and where it should go. The address bus is used to identify particular locations (addresses) in main memory. The width of the address bus (that is, the number of wires) determines how many unique memory locations can be addressed. Modern PCs and Macs have as many as 36 address lines, which enables them theoretically to access 64 GB of main memory. However, the actual amount of memory that can be accessed is usually much less than this theoretical limit due to chipset and motherboard limitations.

    The size of a bus, known as its width, is important because it determines how much data can be transmitted at one time. The bus size actually indicates the number of wires in the bus. For example, a 32-bit bus has 32 wires or connectors that transmit 32 bits simultaneously (referred to as in parallel). It would be considered “32-bits wide.” A 16-bit bus has 16 wires or connectors that can transmit 16 bits of data in parallel. You would say it is “16-bits wide.”

    System Bus & I/O Bus

    On older computers, the local bus, which was the only bus, was used for the CPU, RAM and I/O (input/output) components. All components on the local bus used the same clock speed. In the late 80s we saw the separation of the system bus from the I/O bus allowing them to run at different speeds.

    The system bus (also called the frontside bus, memory bus, local bus or host bus) is what connects the CPU to main memory on the motherboard. I/O buses are those that connect the CPU and RAM with all other components, and the I/O buses branch off of the system bus. I/O buses operate on a speed which is lower than the system bus speed. PCs offer several types of I/O buses which include the ISA bus, PCI bus, AGP bus and USB bus.

    ISA Bus & PCI Bus

    Short for Industry Standard Architecture bus, the ISA bus architecture was used in the IBM PC/XT and PC/AT. The AT version of the bus is called the AT bus and became a de facto industry standard. Starting in the early 90s, ISA began to be replaced by the PCI (Peripheral Component Interconnect) local bus architecture. The PCI standard was developed by Intel Corp. On modern PCs, the PCI bus is the central (or main) I/O bus. It’s used for connecting adapters such as hard disks, sound cards, network cards and graphics cards (although now AGP is more common for 3-D graphics). PCI is a 64-bit bus, though it is usually implemented as a 32-bit bus, and it can run at clock speeds of 33 or 66 MHz. At 32-bits and 33 MHz, it yields a throughput rate of 133 MBps (at 66 MHz 266 MBps). The vast majority of today’s PCs implement a PCI bus that runs at a maximum speed of 33 MHz.

    PCI 2.1

    Also called PCI-X 2.0, the PCI bus specification version 2.1 calls for expandability to 64-bits and 66 MHz speed, yielding a throughput rate of 532 MBps.

    AGP Bus

    Short for Accelerated Graphics Port, an interface specification developed by Intel Corporation. AGP is based on PCI, but is designed especially for the throughput demands of 3-D graphics. Rather than using the PCI bus for graphics data, AGP introduces a dedicated point-to-point channel so that the graphics controller can directly access main memory. The AGP channel is 32-bits wide and runs at 66 MHz. This translates into a total bandwidth of 266 MBps, as opposed to the PCI bandwidth of 133 MBps. AGP also supports optional faster modes and allows 3-D textures to be stored in main memory rather than video memory.

    USB Bus

    Short for Universal Serial Bus, an external bus standard that supports data transfer rates of 12 Mbps. A single USB port can be used to connect up to 127 peripheral devices, such as mice, modems, and keyboards. USB also supports Plug-and-Play installation and hot plugging.

    USB 2.0

    Also referred to as Hi-Speed USB, USB 2.0 is an external bus that supports data rates up to 480Mbps. USB 2.0 is an extension of USB 1.1. USB 2.0 is fully compatible with USB 1.1 and uses the same cables and connectors.

    Bus Speed

    Every bus has a clock speed measured in MHz. This measurement represents the speed in which information and data can move across the bus on the motherboard. A fast bus allows data to be transferred faster, which makes applications run faster. Bus speed is one of the factors which determines the speed of your CPU.

    Backside Bus

    The backside bus is the microprocessor bus that connects the CPU to a Level 2 cache. Typically, a backside bus runs at a faster clock speed than the frontside bus that connects the CPU to main memory. For example, the Pentium Pro microprocessor actually consists of two chips one contains the CPU and the primary cache, and the second contains the secondary cache. A backside bus connects the two chips at the same clock rate as the CPU itself (at least 200 MHz). In contrast, the frontside bus runs at only a fraction of the CPU clock speed.

    Key Terms To Understanding Buses

    A collection of wires through which data is transmitted from one part of a computer to another.

    System Bus
    The bus that connects the CPU to main memory on the motherboard.

    The term I/O is used to describe any program, operation or device that transfers data to or from a computer and to or from a peripheral device.

    Short for Peripheral Component Interconnect, a local bus standard developed by Intel Corp.

    Based in Nova Scotia, Vangie Beal is has been writing about technology for more than a decade. She is a frequent contributor to EcommerceGuide and managing editor at Webopedia. You can tweet her online @AuroraGG.

    This article was originally published on November 04, 2005