All hard drives share a basic structure and are composed of the same physical features. However, not all hard drives perform the same way — the quality of the parts inside the hard drive will affect its performance. Following is a description of the common features of the hard drive and how each part works in relation to the others. Hard drives are extremely sensitive equipment and the internal workings of a hard drive should not be handled by anyone other than an experienced professional. The Platters The platters are the actual disks inside the drive that store the magnetized data. Traditionally platters are made of a light aluminum alloy and coated with a magnetizable material such as a ferrite compound that is applied in liquid form and spun evenly across the platter or thin metal film plating that is applied to the platter through electroplating, the same way that chrome is produced. Newer technology uses glass and/or ceramic platters because they can be made thinner and also because they are more efficient at resisting heat. The magnetic layer on the platters has tiny domains of magnetization that are oriented to store information that is transferred through the read/write heads. Most drives have at least two platters, and the larger the storage capacity of the drive, the more platters there are. Each platter is magnetized on each side, so a drive with 2 platters has 4 sides to store data.

Key Terms To Understanding Hard Drives: hard drive platter spindle heads actuator Related Articles on Webopedia: Formatting a Hard Disk Drive How to Defrag Your Hard Drive Tips to Fix a Slow Running Computer How to Completely Erase a Hard Disk Drive Maintenance Tips for Your PC

The Spindle and Spindle Motor

The platters in a drive are separated by disk spacers and are clamped to a rotating spindle that turns all the platters in unison. The spindle motor is built right into the spindle or mounted directly below it and spins the platters at a constant set rate ranging from 3,600 to 7,200 RPM. The motor is attached to a feedback loop to ensure that it spins at precisely the speed it is supposed to.

The Read/Write Heads

The read/write heads read and write data to the platters. There is typically one head per platter side, and each head is attached to a single actuator shaft so that all the heads move in unison. When one head is over a track, all the other heads are at the same location over their respective surfaces. Typically, only one of the heads is active at a time, i.e., reading or writing data. When not in use, the heads rest on the stationary platters, but when in motion the spinning of the platters create air pressure that lifts the heads off the platters. The space between the platter and the head is so minute that even one dust particle or a fingerprint could disable the spin. This necessitates that hard drive assembly be done in a clean room. When the platters cease spinning the heads come to rest, or park, at a predetermined position on the heads, called the landing zone.

The Head Actuator

All the heads are attached to a single head actuator, or actuator arm, that moves the heads around the platters. Older hard drives used a stepper motor actuator, which moved the heads based on a motor reacting to stepper pulses. Each pulse moved the actuator over the platters in predefined steps. Stepper motor actuators are not used in modern drives because they are prone to alignment problems and are highly sensitive to heat. Modern hard drives use a voice coil actuator, which controls the movement of a coil toward or away from a permanent magnet based on the amount of current flowing through it. This guidance system is called a servo.

The platters, spindle, spindle motor, head actuator and the read/write heads are all contained in a chamber called the head disk assembly (HDA). Outside of the HDA is the logic board that controls the movements of the internal parts and controls the movement of data into and out of the drive.

For more information, see Internal Hard Drive Parts on HardwareCentral.com

By Webopedia.com Staff
Originally published 2002. Last updated January 22, 2010

Webopedia "Did You Know ... Preventative Maintenance Tips for Your PC"
Computer failures occur for a variety of reasons, sometimes because of human error and sometimes because of factors in the environment that cause a computer to malfunction . or a combination of both.

Webopedia "Did You Know ... How to Completely Erase a Hard Disk Drive"
Tips to Avoid Data Theft When Donating a Computer System.

Webopedia "Did You Know ... Formatting a Hard Disk Drive"
When installing a hard disk drive (commonly called a hard drive) for the first time, attempting to remove errors from your drive, getting rid of a nasty virus, or even cleaning a hard drive because you are selling or donating your computer -- those are just a few of the many reasons why one might consider formatting their hard drive.

Webopedia "Did You Know ... The Difference Between a Virus, Worm and Trojan Horse"
While the words Trojan, worm and virus are often used interchangeably, they are not the same. Viruses, worms and Trojan Horses are all malicious programs that can cause damage to your computer, but there are differences among the three, and knowing those differences can help you to better protect your computer from their often damaging effects.

Microsoft OneCare: 3 ways to boost your computer's performance
By doing just a few simple things, you can notice an immediate difference in how your PC performs.

Webopedia "Did You Know ... The System Boot Process"
The typical computer system boots over and over again with no problems, starting the computer's operating system (OS) and identifying its hardware and software components that all work together to provide the user with the complete computing experience.